Difference between revisions of "MSS60 Error: 27B0, P0491"
From Wiki-DIY
(Created page with "__FORCETOC__ ==== '''27B0 - P0491''' ==== {| class = "diyTable ecuFault" |- |'''Information saved in''' |DME |- |'''Fault code''' |27B0 - P0491 |- |'''Fault text''' |Second...") |
(Tag: Visual edit) |
||
| Line 21: | Line 21: | ||
|Test condition: sls_obdh_mdf_max_intg_norm (after roughly 30s)<K_SLS_OBDH_MDF_MIN_DEF and | |Test condition: sls_obdh_mdf_max_intg_norm (after roughly 30s)<K_SLS_OBDH_MDF_MIN_DEF and | ||
|- | |- | ||
| − | | | + | | |
|sls_obdh_lam_asv_intg_norm < k_SLS_OBDH_MDF_2_MAG or | |sls_obdh_lam_asv_intg_norm < k_SLS_OBDH_MDF_2_MAG or | ||
|- | |- | ||
| − | | | + | | |
|sls_obdh_lam_asv_intg_norm < k_SLS_OBDH_ASV_LI_OPE and K_SLS_OBDH_MDF_MIN_DEF>K_SLS_OBDH_MDF_MAX_DEF | |sls_obdh_lam_asv_intg_norm < k_SLS_OBDH_ASV_LI_OPE and K_SLS_OBDH_MDF_MIN_DEF>K_SLS_OBDH_MDF_MAX_DEF | ||
|- | |- | ||
| − | | | + | | |
|Terminal condition: Engine running | |Terminal condition: Engine running | ||
|- | |- | ||
| − | | | + | | |
|Voltage condition: Battery voltage > 10.8 V (k_sls_obd_ub_min) | |Voltage condition: Battery voltage > 10.8 V (k_sls_obd_ub_min) | ||
|- | |- | ||
| Line 39: | Line 39: | ||
|1. Disconnect secondary air line | |1. Disconnect secondary air line | ||
|- | |- | ||
| − | | | + | | |
|2. Carry out test routine | |2. Carry out test routine | ||
|- | |- | ||
| − | | | + | | |
|3. If flow is too high, replace the ASV | |3. If flow is too high, replace the ASV | ||
|- | |- | ||
| − | | | + | | |
|4. Otherwise check Line 1 for obstructions and replace as indicated | |4. Otherwise check Line 1 for obstructions and replace as indicated | ||
|- | |- | ||
Latest revision as of 13:25, 3 February 2015
Contents
27B0 - P0491
| Information saved in | DME |
| Fault code | 27B0 - P0491 |
| Fault text | Secondary air system flow rate, bank 1 |
| Fault description | Secondary Air Injection System Insufficient Flow (Bank 1) |
| Condition for fault identification | Test condition: sls_obdh_mdf_max_intg_norm (after roughly 30s)<K_SLS_OBDH_MDF_MIN_DEF and |
| sls_obdh_lam_asv_intg_norm < k_SLS_OBDH_MDF_2_MAG or | |
| sls_obdh_lam_asv_intg_norm < k_SLS_OBDH_ASV_LI_OPE and K_SLS_OBDH_MDF_MIN_DEF>K_SLS_OBDH_MDF_MAX_DEF | |
| Terminal condition: Engine running | |
| Voltage condition: Battery voltage > 10.8 V (k_sls_obd_ub_min) | |
| Condition for fault memory entry | 30000 ms |
| Action in service | 1. Disconnect secondary air line |
| 2. Carry out test routine | |
| 3. If flow is too high, replace the ASV | |
| 4. Otherwise check Line 1 for obstructions and replace as indicated | |
| Fault effect and breakdown warning | MIL is on after 2x engine cold start |
| Driver information | Warning light: MIL |
| Service instruction | None |
