Difference between revisions of "MSS60 Error: 27AA, P0068, P0106, P2191"
From Wiki-DIY
m (Rcollins moved page MSS60 Erro: 27AA - P0068 to MSS60 Error: 27AA - P0068) |
m (Rcollins moved page MSS60 Error: 27AA - P0068 to MSS60 Error: 27AA, P0068, P0106, P2191) |
||
(11 intermediate revisions by the same user not shown) | |||
Line 1: | Line 1: | ||
− | + | __FORCETOC__ | |
− | + | ||
− | | | + | |
+ | ==== '''27AA - P0106''' ==== | ||
+ | {| class = "diyTable ecuFault" | ||
|- | |- | ||
|'''Information saved in''' | |'''Information saved in''' | ||
Line 32: | Line 34: | ||
| | | | ||
|2. Replace intake manifold pressure sensor | |2. Replace intake manifold pressure sensor | ||
+ | |- | ||
+ | |'''Fault effect and breakdown warning''' | ||
+ | |MIL on after engine runs 2x | ||
+ | |- | ||
+ | |'''Driver information''' | ||
+ | |Warning light: MIL | ||
+ | |- | ||
+ | |'''Service instruction''' | ||
+ | |None | ||
+ | |} | ||
+ | |||
+ | |||
+ | ==== '''27AA - P0068''' ==== | ||
+ | {| class = "diyTable ecuFault" | ||
+ | |- | ||
+ | |'''Information saved in''' | ||
+ | |DME | ||
+ | |- | ||
+ | |'''Fault code''' | ||
+ | |27AA - P0068 | ||
+ | |- | ||
+ | |'''Fault text''' | ||
+ | |Charge plausibility, diagnosis hot - bank 1 | ||
+ | |- | ||
+ | |'''Fault description''' | ||
+ | |MAP/MAF - Throttle Position Correlation | ||
+ | |- | ||
+ | |'''Condition for fault identification''' | ||
+ | |Test condition: Deviation from mean value (depending on psau, lam, aq) in percent is determined and compared with the max. deviation (in relation to rpm/load factor) KF_FPLAU_OBD_AQ_DELTA_ML_MAX * expansion factor (K_FPLAU_OBD_TE_F) | ||
+ | |- | ||
+ | | | ||
+ | |Terminal condition: Engine running | ||
+ | |- | ||
+ | | | ||
+ | |Voltage condition: None | ||
+ | |- | ||
+ | |'''Condition for fault memory entry''' | ||
+ | |10000 ms | ||
+ | |- | ||
+ | |'''Action in service''' | ||
+ | |1. Check induction system B1 for leaks | ||
+ | |- | ||
+ | |'''Fault effect and breakdown warning''' | ||
+ | |MIL on after engine runs 2x | ||
+ | |- | ||
+ | |'''Driver information''' | ||
+ | |Warning light: MIL | ||
+ | |- | ||
+ | |'''Service instruction''' | ||
+ | |None | ||
+ | |} | ||
+ | |||
+ | |||
+ | ==== '''27AA - P2191''' ==== | ||
+ | {| class = "diyTable ecuFault" | ||
+ | |- | ||
+ | |'''Information saved in''' | ||
+ | |DME | ||
+ | |- | ||
+ | |'''Fault code''' | ||
+ | |27AA - P2191 | ||
+ | |- | ||
+ | |'''Fault text''' | ||
+ | |Charge plausibility, diagnosis hot - bank 1 | ||
+ | |- | ||
+ | |'''Fault description''' | ||
+ | |System Too Lean at Higher Load (Bank 1) | ||
+ | |- | ||
+ | |'''Condition for fault identification''' | ||
+ | |Test condition: Deviation from mean value (depending on psau, lam, aq) in percent is determined and compared with the max. deviation (in relation to rpm/load factor) KF_FPLAU_OBD_AQ_DELTA_ML_MAX * expansion factor (K_FPLAU_OBD_TE_F) | ||
+ | |- | ||
+ | | | ||
+ | |Terminal condition: Engine running | ||
+ | |- | ||
+ | | | ||
+ | |Voltage condition: None | ||
+ | |- | ||
+ | |'''Condition for fault memory entry''' | ||
+ | |10000 ms | ||
+ | |- | ||
+ | |'''Action in service''' | ||
+ | |1. Check induction system B1 for leaks | ||
|- | |- | ||
|'''Fault effect and breakdown warning''' | |'''Fault effect and breakdown warning''' |
Latest revision as of 11:16, 10 January 2015
Contents
27AA - P0106
Information saved in | DME |
Fault code | 27AA - P0106 |
Fault text | Charge plausibility, diagnosis hot - bank 1 |
Fault description | Manifold Absolute Pressure/Barometric Pressure Sensor Circuit Range/Performance |
Condition for fault identification | Test condition: Deviation from mean value (depending on psau, lam, aq) in percent is determined and compared with the max. deviation (in relation to rpm/load factor) KF_FPLAU_OBD_PSAU_DELTA_ML_MAX * expansion factors (K_FPLAU_OBD_TE_F, KL_FPLAU_PSAU_PUMG_F) |
Terminal condition: Engine running | |
Voltage condition: None | |
Condition for fault memory entry | 10000 ms |
Action in service | 1. Check induction system B1 for leaks |
2. Replace intake manifold pressure sensor | |
Fault effect and breakdown warning | MIL on after engine runs 2x |
Driver information | Warning light: MIL |
Service instruction | None |
27AA - P0068
Information saved in | DME |
Fault code | 27AA - P0068 |
Fault text | Charge plausibility, diagnosis hot - bank 1 |
Fault description | MAP/MAF - Throttle Position Correlation |
Condition for fault identification | Test condition: Deviation from mean value (depending on psau, lam, aq) in percent is determined and compared with the max. deviation (in relation to rpm/load factor) KF_FPLAU_OBD_AQ_DELTA_ML_MAX * expansion factor (K_FPLAU_OBD_TE_F) |
Terminal condition: Engine running | |
Voltage condition: None | |
Condition for fault memory entry | 10000 ms |
Action in service | 1. Check induction system B1 for leaks |
Fault effect and breakdown warning | MIL on after engine runs 2x |
Driver information | Warning light: MIL |
Service instruction | None |
27AA - P2191
Information saved in | DME |
Fault code | 27AA - P2191 |
Fault text | Charge plausibility, diagnosis hot - bank 1 |
Fault description | System Too Lean at Higher Load (Bank 1) |
Condition for fault identification | Test condition: Deviation from mean value (depending on psau, lam, aq) in percent is determined and compared with the max. deviation (in relation to rpm/load factor) KF_FPLAU_OBD_AQ_DELTA_ML_MAX * expansion factor (K_FPLAU_OBD_TE_F) |
Terminal condition: Engine running | |
Voltage condition: None | |
Condition for fault memory entry | 10000 ms |
Action in service | 1. Check induction system B1 for leaks |
Fault effect and breakdown warning | MIL on after engine runs 2x |
Driver information | Warning light: MIL |
Service instruction | None |