Difference between revisions of "MSS60 Error: 275A, P0358, P131C, P133A, P2321, P2322"
From Wiki-DIY
(Created page with " {| | | |- |'''Information saved in''' |DME |- |'''Fault code''' |275A - P0358 |- |'''Fault text''' |Ignition cylinder 8, activation |- |'''Fault description''' |Ignition Co...") (Tag: Visual edit) |
|||
Line 1: | Line 1: | ||
+ | __FORCETOC__ | ||
− | + | ====275A - P0358==== | |
− | + | {| class = "diyTable ecuFault" | |
− | {| | ||
− | |||
− | |||
|- | |- | ||
|'''Information saved in''' | |'''Information saved in''' | ||
Line 56: | Line 54: | ||
− | + | ====275A - P131C==== | |
− | + | {| class = "diyTable ecuFault" | |
− | |||
− | {| | ||
− | |||
− | |||
|- | |- | ||
|'''Information saved in''' | |'''Information saved in''' | ||
Line 116: | Line 110: | ||
− | + | ====275A - P133A==== | |
− | + | {| class = "diyTable ecuFault" | |
− | |||
− | {| | ||
− | |||
− | |||
|- | |- | ||
|'''Information saved in''' | |'''Information saved in''' | ||
Line 173: | Line 163: | ||
− | + | ====275A - P2321==== | |
− | + | {| class = "diyTable ecuFault" | |
− | |||
− | {| | ||
− | |||
− | |||
|- | |- | ||
|'''Information saved in''' | |'''Information saved in''' | ||
Line 233: | Line 219: | ||
− | + | ====275A - P2322==== | |
− | + | {| class = "diyTable ecuFault" | |
− | |||
− | {| | ||
− | |||
− | |||
|- | |- | ||
|'''Information saved in''' | |'''Information saved in''' |
Latest revision as of 15:02, 3 May 2015
275A - P0358
Information saved in | DME |
Fault code | 275A - P0358 |
Fault text | Ignition cylinder 8, activation |
Fault description | Ignition Coil 'H' Primary Control Circuit/Open |
Condition for fault identification | Test condition: Current on PIN A_S_ICC too low with active ignition pulse |
Terminal condition: TERM87 | |
Voltage condition: Battery voltage > 9.8V (k_diag_tr_ub_min) | |
Condition for fault memory entry | 8 operating cycles |
Action in service | 1. Check plug and wiring harness at M ignition coil |
2. Replace M ignition coil as indicated | |
Fault effect and breakdown warning | CC message |
Engine speed limited | |
Reduced power | |
Rough idle | |
Driver information | Warning light: MIL, EML, CC message, backup program |
Service instruction | None |
275A - P131C
Information saved in | DME |
Fault code | 275A - P131C |
Fault text | Ignition cylinder 8, activation |
Fault description | Ionic Current Control Module Control Line Ignition Cylinder 8 Low |
Condition for fault identification | Test condition: Voltage at PIN A_S_ICC too low, ignition channel inactive |
Terminal condition: TERM87 | |
Voltage condition: Battery voltage > 9.8V (k_diag_tr_ub_min) | |
Condition for fault memory entry | 8 operating cycles |
Action in service | 1. Check plug and wiring harness at M ignition coil |
2. Replace M ignition coil as indicated | |
3. If shorts to ground are entered for all cylinders check fuse for TERM87 power supply | |
Fault effect and breakdown warning | CC message |
Engine speed limited | |
Reduced power | |
Rough idle | |
Driver information | Warning light: MIL, EML, CC message, backup program |
Service instruction | None |
275A - P133A
Information saved in | DME |
Fault code | 275A - P133A |
Fault text | Ignition cylinder 8, activation |
Fault description | Ionic Current Control Module Control Line Ignition Cylinder 8 High |
Condition for fault identification | Test condition: Current on PIN A_S_ICC too high with active ignition pulse |
Terminal condition: TERM87 | |
Voltage condition: Battery voltage > 9.8V (k_diag_tr_ub_min) | |
Condition for fault memory entry | 8 operating cycles |
Action in service | 1. Check plug and wiring harness at M ignition coil |
2. Replace M ignition coil as indicated | |
Fault effect and breakdown warning | CC message |
Engine speed limited | |
Reduced power | |
Rough idle | |
Driver information | Warning light: MIL, EML, CC message, backup program |
Service instruction | None |
275A - P2321
Information saved in | DME |
Fault code | 275A - P2321 |
Fault text | Ignition cylinder 8, activation |
Fault description | Ignition Coil 'H' Primary Control Circuit Low |
Condition for fault identification | Test condition: Voltage at PIN A_S_ICC too low, ignition channel inactive |
Terminal condition: TERM87 | |
Voltage condition: Battery voltage > 9.8V (k_diag_tr_ub_min) | |
Condition for fault memory entry | 8 operating cycles |
Action in service | 1. Check plug and wiring harness at M ignition coil |
2. Replace M ignition coil as indicated | |
3. If shorts to ground are entered for all cylinders check fuse for TERM87 power supply | |
Fault effect and breakdown warning | CC message |
Engine speed limited | |
Reduced power | |
Rough idle | |
Driver information | Warning light: MIL, EML, CC message, backup program |
Service instruction | None |
275A - P2322
Information saved in | DME |
Fault code | 275A - P2322 |
Fault text | Ignition cylinder 8, activation |
Fault description | Ignition Coil 'H' Primary Control Circuit High |
Condition for fault identification | Test condition: Current on PIN A_S_ICC too high with active ignition pulse |
Terminal condition: TERM87 | |
Voltage condition: Battery voltage > 9.8V (k_diag_tr_ub_min) | |
Condition for fault memory entry | 8 operating cycles |
Action in service | 1. Check plug and wiring harness at M ignition coil |
2. Replace M ignition coil as indicated | |
Fault effect and breakdown warning | CC message |
Engine speed limited | |
Reduced power | |
Rough idle | |
Driver information | Warning light: MIL, EML, CC message, backup program |
Service instruction | None |