Difference between revisions of "Engine Specs - S54 Rod Bolts"
From Wiki-DIY
(→SPEC: OEM: Torque procedure) |
|||
| (5 intermediate revisions by the same user not shown) | |||
| Line 4: | Line 4: | ||
The S54 has two different types of connecting rod bolts. The torque procedure for each is different. | The S54 has two different types of connecting rod bolts. The torque procedure for each is different. | ||
| + | * Type-1: M11 x 1.25 mm thread pitch. 12 mm bi-hexagonal bolt head. | ||
| + | * Type-2: M10 x 1.25 mm thread pitch. E12 Torx bolt head. | ||
| − | === OEM Rod Bolts === | + | === OEM Rod Bolts (M11 x 1.25, 12mm bi-hex bolt head) === |
==== SPEC: OEM: Torque procedure ==== | ==== SPEC: OEM: Torque procedure ==== | ||
| Line 13: | Line 15: | ||
!Angle | !Angle | ||
|- | |- | ||
| − | | | + | |30 Nm |
| − | | | + | |70 degrees |
|- | |- | ||
| − | |Remove | + | |Remove bearing cap |
| | | | ||
|- | |- | ||
| − | | | + | |30 Nm |
| − | | | + | |70 degrees |
| + | |} | ||
| + | <br> | ||
| + | Make sure you are starting with new rod bolts. Factory rod bolts must be replaced once used. | ||
| + | # Lubricate rod bolt threads and connecting rod cap bore holes with appropriate thread lubricant. | ||
| + | # Torque to 30-Nm, then using a torque-angle gauge tighten another 70-degrees. | ||
| + | # Remove bolts. | ||
| + | # Repeat steps 1, 2. | ||
| + | <p></p> | ||
| + | |||
| + | === OEM Rod Bolts (M10 x 1.25, E12 Torx bolt head) === | ||
| + | |||
| + | ==== SPEC: OEM: Torque procedure ==== | ||
| + | |||
| + | {| class = "diyTable bearingSpec" | ||
| + | !Torque | ||
| + | !Angle | ||
| + | |- | ||
| + | |30 Nm | ||
| + | |105 degrees | ||
| + | |- | ||
| + | |Release bolts | ||
| + | | | ||
|- | |- | ||
| − | | | + | |30 Nm |
| + | |105 degrees | ||
| + | |- | ||
| + | |Release bolts | ||
| | | | ||
|- | |- | ||
| − | | | + | |30 Nm |
| − | | | + | |105 degrees |
|} | |} | ||
<br> | <br> | ||
Make sure you are starting with new rod bolts. Factory rod bolts must be replaced once used. | Make sure you are starting with new rod bolts. Factory rod bolts must be replaced once used. | ||
# Lubricate rod bolt threads and connecting rod cap bore holes with appropriate thread lubricant. | # Lubricate rod bolt threads and connecting rod cap bore holes with appropriate thread lubricant. | ||
| − | # Torque to | + | # Torque to 30-Nm, then using a torque-angle gauge tighten another 105-degrees. |
| − | # | + | # Release bolts. |
# Repeat steps 1-3 | # Repeat steps 1-3 | ||
# Repeat steps 1, 2. | # Repeat steps 1, 2. | ||
| − | |||
| − | |||
| − | |||
| − | |||
<p></p> | <p></p> | ||
Latest revision as of 14:52, 2 December 2016
Contents
Rod Bolt Comparisons
The S54 has two different types of connecting rod bolts. The torque procedure for each is different.
- Type-1: M11 x 1.25 mm thread pitch. 12 mm bi-hexagonal bolt head.
- Type-2: M10 x 1.25 mm thread pitch. E12 Torx bolt head.
OEM Rod Bolts (M11 x 1.25, 12mm bi-hex bolt head)
SPEC: OEM: Torque procedure
| Torque | Angle |
|---|---|
| 30 Nm | 70 degrees |
| Remove bearing cap | |
| 30 Nm | 70 degrees |
Make sure you are starting with new rod bolts. Factory rod bolts must be replaced once used.
- Lubricate rod bolt threads and connecting rod cap bore holes with appropriate thread lubricant.
- Torque to 30-Nm, then using a torque-angle gauge tighten another 70-degrees.
- Remove bolts.
- Repeat steps 1, 2.
OEM Rod Bolts (M10 x 1.25, E12 Torx bolt head)
SPEC: OEM: Torque procedure
| Torque | Angle |
|---|---|
| 30 Nm | 105 degrees |
| Release bolts | |
| 30 Nm | 105 degrees |
| Release bolts | |
| 30 Nm | 105 degrees |
Make sure you are starting with new rod bolts. Factory rod bolts must be replaced once used.
- Lubricate rod bolt threads and connecting rod cap bore holes with appropriate thread lubricant.
- Torque to 30-Nm, then using a torque-angle gauge tighten another 105-degrees.
- Release bolts.
- Repeat steps 1-3
- Repeat steps 1, 2.
